4[4]x4[4] Analog Mux
This board is designed for routing is 2 sets of 4 to 1 audio (i2s) lines (bck, fs, rd, wd) for test automation and probing. However, due to the use of analog muxes, it definitely has additional uses and can be used as an all-around analog mux with limited analog bandwidth (datasheet suggests up to 100Mhz for -3db but the board routing at 2 layers probably creates a constraint lower than this. See datasheet for details.) The routing is control is via an i2c gpio expander chip and can be interfaced to any supporting microcontroller.
4[4]x4[4] Analog Mux
*PCBWay community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.

Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW
ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor
BUY NOW
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW- Comments(0)
- Likes(0)

- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by DigitalArtisans.org
-
4[4]x4[4] Analog Mux This board is designed for routing is 2 sets of 4 to 1 audio (i2s) lines (bck, fs, rd, wd) for test ...
-
IDE Breakout board A simple pass-through snooping board for snooping a full sized IDE disk. Lines are brought to 2.54mm...
-
Single Channel Audio Meter Single Channel Audio Meter
-
1.27mm Breakout Board Allows for interfacing to 1.27 mm components on a 2.54 mm breadboard and vice versa. Header pins can...
-
Mimas FGPA Tektronix TLA Breakout Board This is a board to bring out all pins of the Mimas FPGA to headers used by Tektronix TLA probes. It ...
-
DS1245YP Replacement Board v2 A solder-in replacement for the DS1245YP to eliminate battery replacement problems.BOM and instructi...
-
Modifying a Hotplate to a Reflow Solder Station
397 0 4 -
MPL3115A2 Barometric Pressure, Altitude, and Temperature Sensor
239 0 1 -
-
Nintendo 64DD Replacement Shell
256 0 1 -
V2 Commodore AMIGA USB-C Power Sink Delivery High Efficiency Supply Triple Output 5V ±12V OLED display ATARI compatible shark 100W
635 4 2 -
How to measure weight with Load Cell and HX711
504 0 3 -
-
Instrumentation Input, high impedance with 16 bit 1MSPS ADC for SPI
595 1 0